Fundamental Plumbing Tips for Installing a Bathtub
Fundamental Plumbing Tips for Installing a Bathtub
Blog Article
Are you currently trying to locate information on Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a reasonably tough job. If the old tub is conveniently available, the project can relocate immediately; if you have to open up a wall to remove the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified on your own for the task as well as fit attempting it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly help you mount a brand-new bath tub in your shower room if you have currently acquired a brand-new tub and also do not require to change the setup of your previous water pipes.
Your tools and also product list must comprise the following:
Planning for the Installment
Firstly, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps unit to stop strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last placement.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be quite problematic due to the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the required setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by examining the level as well as changing the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water system as well as inspect all joints and brand-new pipework for leaks and also tighten them if needed. Load the tub as well as also inspect the overflow electrical outlet and also the typical electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the tub ought to wait up until the bath tub has actually been used at least when as this will resolve it into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin making sure that the washers remain in location in between the tap and the sink. Protect the tap in place with the manufacturer provided backnut. Once the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, resulting in complications with wetness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can split rather early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise easily available on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our topic on Installing A Bathtub. Thanks a ton for taking time to read our content. In case you liked our post kindly be sure to pass it around. I love reading our article about How to Install a Bathtub Yourself.
Urgent plumbing issue? Connect now. Report this page